How To Mix Joint Compound And Paint For Texture

Download Commodity

Download Article

There are a variety of techniques y'all can utilize to texture drywall. Some techniques, such as the orange peel, require the use of a hopper gun. Others, like the sand swirl, but require a wide castor. Each technique has its own character, and all of them offer the opportunity to be creative.

1
Sand your drywall . Use a sanding pole to set your walls for drywall texturing. A pole with a rounded sander will allow you to remove material faster. Try to get the wall equally shine as possible.^[i]
- Apply a sanding sponge to sand any difficult angles or corners. You can also use the sanding sponge for detail piece of work.^[2]
- Use a fine grit sandpaper to sand your drywall. Sand with calorie-free pressure level to avoid ruining the texture of the wall.^[3]
- Wear protective goggles and a dust mask when sanding. Sanding drywall releases small particles of drywall grit that will get everywhere. Make certain you're protected.^[4]
ii
Prime your drywall. Remove whatever dust remaining from the sanding procedure with a clammy cloth. Use a brush to prime the edges virtually the ceiling line, and use a roller to coat the walls. A high quality primer should go on in a unmarried coat.^[5]
- Before priming, lay down some protective covering such equally plastic or heavy cloth. Cover any valuables that can't be moved from the room. Primer's main role is to stick to a surface, making it hard to remove.^[6]
- Some professionals recommend priming the drywall earlier you texture to assistance the chemical compound stick. Others recommend priming afterwards you texture to give your pattern a nice terminate. The pick is yours.^[7] ^[eight]
Advertisement
3
Mix your drywall compound. Fill a make clean five gallon saucepan with about five parts powdered drywall mix and thirty parts water. The chemical compound should look like sparse batter.^[ix]
- If yous're using a premixed compound gradually add water until you find the right consistency.^[10]
- Write down the ratios y'all used so yous tin can make go along the chemical compound consistent in case you run out.^[11]
- A drill with a ribbon mixer attachment makes this job considerably easier. Y'all can also allow the chemical compound sit overnight to dissolve any lumps. Exist sure to mix it again before texturing your wall.^[12]
Ad

one
Rent or purchase a hopper gun and air compressor. Y'all tin can discover hopper guns at most hardware stores, or online. If y'all plan on doing a lot of drywall texturing, you may find information technology more cost effective to purchase one of your own. If this is a onetime project, consider renting your hopper gun.
- Attach the hopper gun to an air compressor and load the hopper with your mixed drywall compound.^[thirteen]
- Read the manufacturer's instructions before operating the hopper gun.^[14]
- Only fill the hopper upward about halfway to go along information technology from getting too heavy.^[15]
ii
Arrange the air pressure. The air pressure needs to be high plenty to spray the compound from the gun, but not so high that yous can't control the spray.^[16]
- The gun should as well have an adjustable aperture, or mouth. Accommodate this opening to your liking. A wider opening will create bigger blobs, and a smaller 1 will create a finer texture.^[17]
iii
Do your technique. Before you spray your unabridged room, do a few exam sprays on some chip cardboard or drywall. Brand whatsoever final adjustments to the force per unit area and aperture.^[eighteen]
- Write downward the settings you used in instance y'all want to make the same effect again.^[19]
4
Spray your drywall. Cover your wall in a continuous, sweeping motion. Don't suspension when spraying as this volition cause build up on your wall. Spray with a light touch for all-time results.^[xx]
- You can spray in vertical or horizontal lines, or even in a random design. How yous decide to spray is up to you, just go on in listen y'all're aiming for a uniform application.^[21]
- If you lot feel some of the texture is too thin, y'all can make another pass. Nevertheless, be careful non to spray also much. It can be difficult to friction match up the textures when doing touch-ups.^[22]
five
Finish the texture. Your texture isn't complete until yous paint it. Before you lot paint your drywall, add together another coat of primer. One time the primer dries, add together one or 2 coats of paint to finish the chore.^[23]
- Let the drywall texture dry completely before painting.^[24]
Advertisement

ane
Assemble your supplies. All y'all need to do a sand swirl drywall texture is a wide castor, nearly 7 inches (17.8 cm) long.^[25]
- You tin can replace the drywall compound with a mixture known as perlite, which is primer with sand mixed in. The fine grit of the sand adds another dimension to this texture.^[26]
- If yous choose to do swirls with just the drywall compound, you lot may demand to thin it out a lilliputian more to go fifty-fifty swirls.^[27]
2
Load the castor. To get the right result from this texture, load the brush and wipe abroad whatsoever excess chemical compound. You lot don't want your brush to have and then much compound that it drips on your wall.^[28]
- Don't concur the castor by the handle. Grip the castor and then that your hand is really touching the beard. This volition give y'all amend control when making the swirl pattern.^[29]
3
Kickoff your pattern nigh the ceiling. Outset at one stop of the wall and work your way over in a horizontal line. Place your castor several inches below the ceiling and make a half-moon shape.^[30]
- When you showtime the next swirl, place your castor on the spot where your half-moon ended. This volition create a nice overlapping effect.^[31]
- Work your style down the wall. The elevation of each swirl should cover the bottom of the row above information technology, so that all the swirls overlap.^[32]
- Exercise your technique on some scrap cardboard or drywall before attempting the texture on your wall.^[33]
4

Cease the texture. Once the compound or perlite has dried, add another glaze of primer. Allow the primer dry and then paint the room as normal.^[34]

Advertisement

i
Gather your supplies. To create the slap brush texture y'all volition need a paint roller and some texture brushes. If y'all plan on doing the ceiling as well, become a pole for your roller and brushes.^[35]
- Yous can observe these at any hardware store. The texture brushes may be marketed as "crow's foot" brushes.^[36]
two
Roll out your compound. Load your pigment roller up with drywall compound and start rolling in vertical lines. When you finish rolling one direction, repeat the procedure in the reverse direction. Y'all aren't adding more than mud to the wall, rather your goal is to make an even surface.^[37]
- After you lot've rolled in the opposite management, brand another laissez passer with horizontal lines. Crossing directions helps to polish out any lines from rolling.^[38]
- Work with a 1/2 inch to 3/4 inch (i.25 to ii cm) roller for best results.^[39]
- As yous pull the roller out, give it a slight shake to remove any backlog mud. Equally you utilize the compound, yous desire to avoid dripping chemical compound down your walls.^[40]
- If y'all have a hopper gun, you tin cull to spray the compound on the wall rather than roll it. Either way, try to keep the layer even.^[41]
3
Load upwards your texture castor. Utilise a generous amount of drywall compound to your texture brush. Hold the brush perpendicular to the wall and "stamp" the brush onto the wall.^[42]
- Pull the castor off the wall and keep stamping the wall, working in sections. To vary the pattern, brand half turns with the castor with every stamp. Don't plough the castor while it is touching the wall, equally that will make a smoother, swirled pattern. The goal of the slap brush technique is a crude texture.^[43]
iv
Wipe the angles. Dip a taping knife into some of the drywall chemical compound and run it beyond the edges to smooth out any angles.^[44]
- Wipe the corners from the inside out. Put the border of the brush into the corner and pull away from the bending.^[45]
five

Finish the texture. Let the drywall compound dry out completely before adding some other coat of primer. In one case the primer has dried, paint the room every bit normal.

Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advert

Lay a drop cloth over your flooring and remove all pieces of furniture earlier texturing your walls. Doing so will protect your room and effects from primer or splatter. You lot should also vesture clothes that you exercise non mind getting dirty.
Always wear protective goggles.
Before you begin, mask off any area of the wall or ceiling that you do non want to texture.
Effort wiping with a wet sponge to help go on the grit downward.

Advert

Things Y'all'll Need

Sanding pole
Medium sanding sponge
Mud (articulation chemical compound)
Water
Mud masher or electric drill with paddle
Perlite
Large bucket
Hopper gun, air compressor, and hose
Wide paintbrush
Pigment roller
Slap castor
Primer
Paint
Drop cloths and plastic covering

About This Article

Commodity Summary X

One of the easiest ways to texture drywall is the slap brush technique, which requires a pigment roller and texture castor. To brainstorm, load your paint roller with drywall compound and roll in vertical lines. When you cease ane direction, repeat the process in the opposite direction. And then, use a generous amount of drywall chemical compound to your texture brush and stamp the brush on the wall. You tin can vary your pattern by one-half turning the brush before each postage. After the drywall compound dries, add together a coat of primer, and you're ready to paint. To learn more from our General Contractor co-writer, similar how to utilise a hopper and air compressor to add together drywall texture, keep reading the article!

Did this summary aid yous?

Thank you to all authors for creating a folio that has been read 270,147 times.